Installation and selection of fluoroplastic lined centrifugal pumps

 In the industrial field, fluoroplastic lined centrifugal pumps are widely used in various chemical, pharmaceutical, petroleum and other industries due to their unique performance and advantages. This article will introduce the installation and selection points of fluoroplastic lined centrifugal pump in detail.

 

PFA lined centrifugal pumps

 

Installation and selection of fluoroplastic lined centrifugal pumps

 

Installation points

1. Stable foundation: Make sure the installation foundation is flat and firm to avoid vibration of the pump during operation.

2. Correct connection: Install the pump in strict accordance with the requirements of piping connection and pay attention to sealing to prevent leakage.

3. Power wiring: the connection of power lines should comply with electrical safety standards.

4. Axial level: Ensure the axial level of the pump to avoid tilting causing operation failure.

5. Lubrication and cooling: add appropriate amount of lubricant or coolant as required.

6. Test run: After installation is completed, carry out the necessary test run to check the running status of the pump.

 

The main points of selection​

1. flow and head: according to the process to determine the required flow and head. 2.

2. Medium nature: Consider the temperature, corrosivity, viscosity and other factors of the medium.

3. pump material: choose the fluorine plastic lining material suitable for the medium to ensure corrosion resistance.

4. power and efficiency: according to the actual demand to select the appropriate power and efficiency.

5. sealing form: according to the nature of the medium and working conditions to choose the appropriate sealing form.

6. Brand and quality: choose well-known brands and reliable quality products.

7. cost considerations: under the premise of meeting the demand, consider the cost factor.

 

In short, the correct installation and selection is to ensure the normal operation of fluoroplastic lined centrifugal pumps and play the key to the best performance. In the selection process, various factors should be considered comprehensively to meet the process requirements and reduce operating costs.

 

I hope this article can help you, if you have other questions or need further help, please feel free to visit www.hkpump-valve.com

Comments

Post a Comment

Popular posts from this blog

QBK-T Cast Iron Pneumatic Diaphragm Pumps

Image
  QBK pneumatic diaphragm pump is a new type of conveying machinery, adopting compressed air as the power source, which has the advantages of long service life and will not stop. Its performance parameters are similar to those of WLLDENPVMPS of Federal Germany and MARlOWPUMPS of the United States. It can not only pump the flowing liquid, but also can transport some medium which is not easy to flow, for all kinds of corrosive liquid, liquid with particles, high viscosity, volatile, flammable, highly toxic liquid, can be pumped up and sucked out. QBK air operated diaphragm pump  has many advantages of self-priming pumps, submersible pumps, shielding pumps, slurry pumps and impurity pumps and other conveying machinery. QBK pneumatic diaphragm pump  performance: 1 、 No need to pour water, suction range up to 6m, head up to 70m. 2, flow spacious, through the performance is good, allowing through the largest particle diameter of 10mm. pumping slurry, impurities, the pump wear and tear is ver
Read more

IMD Fluoroplastic Magnetic Pumps

Image
  Brief introduction of IMD PTFE magnetic pump The main parts of IMD PTFE magnetic pump are lined with steel F46, the pump body is of high strength, the high performance magnetic material “NdFeB” is used as inner and outer magnets, and the isolation sleeve is made of non-metallic material, which greatly reduces the magnetic vortex loss, and it can convey the strong corrosive medium with high concentration and density more than 1.9t/m3. The structure is designed as back-pulling type, and the external and installation dimensions of IMD fluoroplastic magnetic pump  are designed and manufactured in accordance with international standards. All specifications are of direct motor connection type, which is supported by the middle bracket, compact structure and easy disassembly. When overhauling and replacing the parts, the core parts can be pumped out directly from the back without disassembling the pipeline and base, which saves the maintenance and cost of working hours.IMD fluorine plastic m
Read more