GMC Stainless Steel Vertical Magnetic Pipeline Pump

 Stainless steel magnetic pipeline pump introduction

GMC stainless steel magnetic pipeline pump is a new type of pipeline pump developed on the basis of the experience of horizontal magnetic pump, which has the characteristics of pipeline centrifugal pump and the advantages of magnetic chemical pump, and is a new generation of leakage-free pipeline centrifugal pump. It can be widely used in chemical, pharmaceutical, petroleum, electroplating, food, national defense industry and other units to pump acid, alkali, oil, rare and precious liquid, poisonous liquid, volatile liquids, as well as circulating water equipment, filtration machine supporting. Especially for the pumping of leakage, flammable and explosive liquids, it is more ideal to use this pump with explosion-proof motor.



Huakai stainless steel magnetic pipeline pump features

1, GMC stainless steel magnetic pipeline pump pipeline pump for vertical structure, the same caliber inlet and outlet, and is located on the same centerline;

2、Impeller is directly connected with motor shaft, high efficiency, energy saving, low noise, can effectively balance the radial and axial load generated by the pump operation;

3、The shaft sleeve is made of high wear-resistant silicon carbide and tungsten carbide, the sliding bearing is made of carbon graphite, and lubricating oil groove is set up to effectively ensure the service life of the pump;.

4、Simple structure, easy maintenance, low vibration, low noise, especially smooth operation; small footprint, no need to disassemble the pipeline when overhauling and replacing the impeller, seals and other wearing parts.
GMC stainless steel magnetic pipeline pump parameters

Product alias: GMC vertical magnetic pipeline pumps

Main material: stainless steel

Flow range: 1.9~120m³/h

Head range: 7.5~80m

Using temperature: -15°C-120°C

Power range：1.1~75Kw

 

Comments

Post a Comment

Popular posts from this blog

QBK-T Cast Iron Pneumatic Diaphragm Pumps

Image
  QBK pneumatic diaphragm pump is a new type of conveying machinery, adopting compressed air as the power source, which has the advantages of long service life and will not stop. Its performance parameters are similar to those of WLLDENPVMPS of Federal Germany and MARlOWPUMPS of the United States. It can not only pump the flowing liquid, but also can transport some medium which is not easy to flow, for all kinds of corrosive liquid, liquid with particles, high viscosity, volatile, flammable, highly toxic liquid, can be pumped up and sucked out. QBK air operated diaphragm pump  has many advantages of self-priming pumps, submersible pumps, shielding pumps, slurry pumps and impurity pumps and other conveying machinery. QBK pneumatic diaphragm pump  performance: 1 、 No need to pour water, suction range up to 6m, head up to 70m. 2, flow spacious, through the performance is good, allowing through the largest particle diameter of 10mm. pumping slurry, impurities, the pump wear and tear is ver
Read more

Installation and selection of fluoroplastic lined centrifugal pumps

Image
  In the industrial field,   fluoroplastic lined centrifugal pumps   are widely used in various chemical, pharmaceutical, petroleum and other industries due to their unique performance and advantages. This article will introduce the installation and selection points of fluoroplastic lined centrifugal pump in detail.   PFA lined centrifugal pumps     Installation points 1. Stable foundation: Make sure the installation foundation is flat and firm to avoid vibration of the pump during operation. 2. Correct connection: Install the pump in strict accordance with the requirements of piping connection and pay attention to sealing to prevent leakage. 3. Power wiring: the connection of power lines should comply with electrical safety standards. 4. Axial level: Ensure the axial level of the pump to avoid tilting causing operation failure. 5. Lubrication and cooling: add appropriate amount of lubricant or coolant as required. 6. Test run: After installation is completed, carry out the necessary t
Read more

IMD Fluoroplastic Magnetic Pumps

Image
  Brief introduction of IMD PTFE magnetic pump The main parts of IMD PTFE magnetic pump are lined with steel F46, the pump body is of high strength, the high performance magnetic material “NdFeB” is used as inner and outer magnets, and the isolation sleeve is made of non-metallic material, which greatly reduces the magnetic vortex loss, and it can convey the strong corrosive medium with high concentration and density more than 1.9t/m3. The structure is designed as back-pulling type, and the external and installation dimensions of IMD fluoroplastic magnetic pump  are designed and manufactured in accordance with international standards. All specifications are of direct motor connection type, which is supported by the middle bracket, compact structure and easy disassembly. When overhauling and replacing the parts, the core parts can be pumped out directly from the back without disassembling the pipeline and base, which saves the maintenance and cost of working hours.IMD fluorine plastic m
Read more